CCNA Exploration 2 – Module 3 Exam Answers(100%)

Expect minimum percentage: 100%

1) Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.

2) Which two statements are true regarding classless routing protocols? (Choose two.)
sends subnet mask information in routing updates
allows for use of both and subnets in the same topology

3) Which command would the network administrator issue to determine if load balancing is in effect on a router?
show ip route

4) Which statement is true regarding routing protocols?
EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.

5) An engineer creates a static route by entering the Router(config)# ip route command. What can be concluded about this route?
The administrative distance of this route is 1.

6) Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network is using a hub and spoke topology
the network is using a flat design

7) Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network

8) What is the purpose of a routing protocol?
It allows a router to share information about known networks with other routers.

9) Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
Administrative distance refers to the trustworthiness of a particular route.
Routes with the smallest metric to a destination indicate the best path.

10)Which of the following best describes the operation of distance vector routing protocols?
They send their routing tables to directly connected neighbors.

11) Which of the following is associated with link-state routing protocols?
shortest-path first calculations

12) The following line of code is displayed in a routing table:
R [120/2] via, 00:00:16, S0/0/0
What can be concluded from this output?
The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.

13) Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers may make incorrect forwarding decisions until the network has converged.

14) Which of the following conditions must be met in order for a network to have converged
The routers in the network are operating with consistent routing knowledge.

15) Which two statements are true regarding the advantages of the use of static routes? (Choose two).

increased security
the administrator maintains control over routing

16) Which two statements are true regarding metrics? (Choose two.)
EIGRP uses bandwidth as a metric.
OSPF uses cost based on bandwidth as a metric.

17) What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address
ORL(config-if)# no shutdown
A routing table entry is made to the network with a code of “C”.

18) Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
The administrative distance of the route to network will be 90.

19) A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
OSPF can be used between the routers.

20) A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
The router will install both routes in the routing table and load balance between the two.

21) The following line of code is present in the routing table:
O [110/129] via, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
The cost for this link has a value of 129.

22) When multiple routing protocols have a route to the same destination network, what determines which route is installed in the routing table?
lowest administrative distance

Written by masputra in: CCNA Exploration 2 : ERouting Chapter 3 |

Powered by WordPress. Theme: TheBuckmaker. Zinsen, Streaming Audio